I built the QLG1 GPS receiver today - went together really quickly. Took me a little longer to figure out exactly how you were supposed to setup the QCX for it (some of the bits about setting frequency were a little vague), but got it up and had great results. 10,000 miles on 2 watts! Got South Africa (2), Canary Islands, Sao Paulo, and Hawaii (2).
Tried calling CW a bit after that, but no takers. (Got spotted in Texas on RBN, so at least I was getting out.)
Saturday, March 7, 2020
Sunday, March 1, 2020
First QSO!
After I posted my last post, I called CQ a few more times... AND SOMEONE CAME BACK!
I ended up having a nice little chat with Roy, WB6OVV. Who turns out actually lives a couple of blocks over from me! He's apparently been doing this for 55 years, but was very patient with my ham-fisted fist. Did tell me to slow down and that operators would usually match your speed. I hope I didn't embarrass myself too badly - I got so excited I kind of forgot the whole "qso format" thing, so was desperately googling while he was sending. I relied on the QCX decoder more than I wanted, but actually was copying find once I calmed down.
So exciting!
(For my future reference, it was 8:15p March 1, 2020 on 7.022.)
I ended up having a nice little chat with Roy, WB6OVV. Who turns out actually lives a couple of blocks over from me! He's apparently been doing this for 55 years, but was very patient with my ham-fisted fist. Did tell me to slow down and that operators would usually match your speed. I hope I didn't embarrass myself too badly - I got so excited I kind of forgot the whole "qso format" thing, so was desperately googling while he was sending. I relied on the QCX decoder more than I wanted, but actually was copying find once I calmed down.
So exciting!
(For my future reference, it was 8:15p March 1, 2020 on 7.022.)
CW!
I've been doing CW.
Specifically, I challenged myself to practice every day for 90 days. I even got people on reddit to do it, too. That's been going pretty well, but I couldn't actually *use* it.
So I decided to build a kit. I ordered the QCX a while back, just finished it today. It takes a while to go together (really dense board), but the instructions are great. I got it up and it worked right away... then stopped. I could still see a *tiny* signal on the scope, but not the several watts I was seeing before. So I figured I blew the finals. But before I pulled anything out, I poked around, emailed the list, asked on reddit chat. And eventually found that the last toroid in the BPF wasn't connected anymore. I had definitely checked it, and it was definitely working, but something must have shifted. Anyway, burned off some more enamel and I was in business.
Was not sure my antenna was going to work - there are a few cuts in the coax - but tested with the nanovna and it looks to still be working.
I lashed up my homemade paddle to a cut-up headphone cord and sent out my CQ.
And someone heard me! Well, RBN again, but still!
KO7SS - 753 miles away on something like 2.5 watts!
Sunday, February 2, 2020
Old amp with new source
Getting back on the bench a bit after a while. After tidying up, thought I would try fishing out the "Mighty Mike" amp I build a few years back out of the box and try it with the Si5351. After putting on a new heat sink and soldering back on a cap that had come off, I hooked it up. Wasn't getting anything at first and not sure why. Went through hunting for shorts/opens and didn't find any. But after doing that, tried again and it worked. I'm getting 1w with 12v supply and 2w with 15v supply.
Wednesday, January 8, 2020
On the workbench - 8Jan20
I haven't been taking many notes here, but have had the iron out.
First, I've been trying a Class E amplifier with an IRF510 being driven from a IXDD614CI Mosfet driver. Since the Si5351 doesn't have enough oomph to drive that driver, I had a little amplifier in front of it. Actually, at first I had a 2n2222 there, but it didn't seem to be operating quite like it did in simulation. I managed to get about a watt out, which was about 7 watts less that I was aiming for. It looked like the peak of the amp wasn't as high as I thought, so I don't think I was getting a 50% duty cycle to the IRF510. So I tried a different tack with two 2n7000 acting as a level shifter instead of the amp.
Not sure what I did in all this, but I suspect I blew the driver. Need to play more, but the last I left it, if I had the driver enabled, the constant current mode in my power supply would kick in. So that's not good. (Though the fact I have that is *awesome* - I love having a proper supply.)
I need to pull more parts off the board and test one by one. I should have built it more incrementally, but I was told I shouldn't run the driver without a load, so didn't know what I could leave off. In retrospect, I should have had it just feed into a 180pF cap (ie, the input capacitance of the IRF510) and make sure that was working first.
I wanted a bit of a break from that, so I tried out a TC4420 that I had (driving a cap). That looks ok... except it doesn't look to be able to handle doing more than 4Mhz. So, might work for 80/160M, but doesn't look like it is going to work for me right now.
First, I've been trying a Class E amplifier with an IRF510 being driven from a IXDD614CI Mosfet driver. Since the Si5351 doesn't have enough oomph to drive that driver, I had a little amplifier in front of it. Actually, at first I had a 2n2222 there, but it didn't seem to be operating quite like it did in simulation. I managed to get about a watt out, which was about 7 watts less that I was aiming for. It looked like the peak of the amp wasn't as high as I thought, so I don't think I was getting a 50% duty cycle to the IRF510. So I tried a different tack with two 2n7000 acting as a level shifter instead of the amp.
Not sure what I did in all this, but I suspect I blew the driver. Need to play more, but the last I left it, if I had the driver enabled, the constant current mode in my power supply would kick in. So that's not good. (Though the fact I have that is *awesome* - I love having a proper supply.)
I need to pull more parts off the board and test one by one. I should have built it more incrementally, but I was told I shouldn't run the driver without a load, so didn't know what I could leave off. In retrospect, I should have had it just feed into a 180pF cap (ie, the input capacitance of the IRF510) and make sure that was working first.
I wanted a bit of a break from that, so I tried out a TC4420 that I had (driving a cap). That looks ok... except it doesn't look to be able to handle doing more than 4Mhz. So, might work for 80/160M, but doesn't look like it is going to work for me right now.
Wednesday, January 1, 2020
New Year, New Band Pass Filter
I wanted to use my new rtl-sdr I got for Christmas on the 40m band (using my dipole). But I was worried about what noise I might get in there, so I decided I'd make a band pass filter. I used this design from ARRL. I put it in a little hexagon box some sort of soap came in. Possibly not the best idea - it was kind of hard to get the BNC connections is, but it worked out. I measured it with the nanoVNA, and it looked like a band pass filter, so that is good. I'm not sure I've calibrated anything else, as it looks like there is a lot of insertion loss that I don't really think is there. Will need to look into that.
Sunday, December 29, 2019
CQ CQ CQ!
I've been trying to figure out what transmitter I want to build next - spending a lot of time modeling it in LTSpice and trying to figure out how it will work.
But I wanted to actually get on the air. I've been practicing my Morse a bit lately, so thought I should just see what I could throw together.
The things I had that were is somewhat working state (or could be made to be...) were my direct conversion receiver and a NS-40 CW transmitter. First thing was I needed a way to connect them. I wanted to make something with a relay and have the Arduino I was using for VFO switch it. But I didn't have any lying around I could find. But I did find a DPDT switch, so I made a little thing in a nuts tin
When the switch is in the transmit position, the transmitter is routed into the dummy load (I didn't want risk accidentally powering it with no load). It doesn't give good isolation - the receiver screams when I key - but seems to somewhat do the trick. Here it is spread over the table:
I tried to send with my homemade key but wasn't getting any responses. I wasn't sure if it was my antenna setup, the low power, or my bad sending. So I thought I should try using a keyer. I found the k3ng Arduino keyer which looked like it would do the trick.
It went together pretty quickly. The ns-40 had some interface circuits on the site that worked well. Only thing is the circuit works on active being low, so I had to switch high and low in the software.
It was getting late, so I wanted to just do a quick test. The keyer has a CW keyboard mode, so I sent CQ from there. I didn't get anyone coming back. But I did get spots on the reverse beacon network!
Very exciting!
But I wanted to actually get on the air. I've been practicing my Morse a bit lately, so thought I should just see what I could throw together.
The things I had that were is somewhat working state (or could be made to be...) were my direct conversion receiver and a NS-40 CW transmitter. First thing was I needed a way to connect them. I wanted to make something with a relay and have the Arduino I was using for VFO switch it. But I didn't have any lying around I could find. But I did find a DPDT switch, so I made a little thing in a nuts tin
When the switch is in the transmit position, the transmitter is routed into the dummy load (I didn't want risk accidentally powering it with no load). It doesn't give good isolation - the receiver screams when I key - but seems to somewhat do the trick. Here it is spread over the table:
I tried to send with my homemade key but wasn't getting any responses. I wasn't sure if it was my antenna setup, the low power, or my bad sending. So I thought I should try using a keyer. I found the k3ng Arduino keyer which looked like it would do the trick.
It went together pretty quickly. The ns-40 had some interface circuits on the site that worked well. Only thing is the circuit works on active being low, so I had to switch high and low in the software.
It was getting late, so I wanted to just do a quick test. The keyer has a CW keyboard mode, so I sent CQ from there. I didn't get anyone coming back. But I did get spots on the reverse beacon network!
Very exciting!
Subscribe to:
Posts (Atom)








